Magnetic + Mechanical + Sensor Based Sorting & Cleaning Solutions to Reduce, Reuse, Recycle.
1 (519) 582-1386 (EST)
This product may be covered by one or more trade secrets, and pending or issued patents and trademarks. For a listing of our registered intellectual property, See Bluestreak Patent Information..
The Khamsin Adjustable Offroad Hanging Magnetic Sweeper was designed specifically to pick up and remove ferrous metal debris that causes flat tires such as nails, screws, wire, discarded pieces of metal from fabrication activities, bolts, nuts, pins, miscellaneous metal pieces, lost tools, etc.
Use the Khamsin’s actuators to raise and lower the magnet when needed such as between job sites. Allows the magnet to remain mounted and travel on the highway with it up, and then lower when needed to start sweeping for debris. Also allows very fine tuning of sweeper height not possible with just chains alone.
To start using the magnetic sweeper just lower the Khamsin by turning the actuators on each end using a cordless drill so that the bumper wheels are just slightly above the ground.
The Bumper wheels are designed to hang slightly above ground but protect the magnet from hitting the ground when truck suspension compresses, or if there are bumps in the road, or when inclines are encountered. Allows you to hang the magnet lower for better performance than would be possible without bumper wheels.
Permanently charged C8 Ceramic Magnets provide a strong magnetic field with a maximum lifting height of 9” inches using a 2.5” inch nail.
Comes standard with a Quick clean off sleeve which allows quick removal of debris even when mounted under a vehicle. Also comes standard with 6 stabilizing chains.
Price range: $3,535.00 through $4,377.00
See Pricing For All Models Below
$3,535.00 CAD
$3,816.00 CAD
$4,082.00 CAD
$4,377.00 CAD
| Khamsin Series | Khamsin 62 | Khamsin 74 | Khamsin 86 | Khamsin 98 |
|---|---|---|---|---|
| SKU | KM62/4.5 | KM74/4.5 | KM86/4.5 | KM98/4.5 |
| Sweeper Width | 62″ | 74″ | 86″ | 98″ |
| Cleaning Method | Quick Clean Off Sleeve | Quick Clean Off Sleeve | Quick Clean Off Sleeve | Quick Clean Off Sleeve |
| Sweeping Height Adjustability | Yes, 2.5” minimum, 3” recommended, 5” maximum | Yes, 2.5” minimum, 3” recommended, 5” maximum | Yes, 2.5” minimum, 3” recommended, 5” maximum | Yes, 2.5” minimum, 3” recommended, 5” maximum |
| Magnet Type | Ceramic 8 | Ceramic 8 | Ceramic 8 | Ceramic 8 |
| Maximum Lifting Height (using a 2.5″ nail) | 9 inches | 9 inches | 9 inches | 9 inches |
| Ground Clearance | adjustable, with a minimum of 2.5” inches | adjustable, with a minimum of 2.5” inches | adjustable, with a minimum of 2.5” inches | adjustable, with a minimum of 2.5” inches |
| Wheels | 10” x 3” Foam Filled flat proof bump wheels with steel hubs and 5/8” ball bearings rated at 136 kg (300 lbs) capacity each | 10” x 3” Foam Filled flat proof bump wheels with steel hubs and 5/8” ball bearings rated at 136 kg (300 lbs) capacity each | 10” x 3” Foam Filled flat proof bump wheels with steel hubs and 5/8” ball bearings rated at 136 kg (300 lbs) capacity each | 10” x 3” Foam Filled flat proof bump wheels with steel hubs and 5/8” ball bearings rated at 136 kg (300 lbs) capacity each |
| Housing Construction | 1/8” thick 6061 Aluminum | 1/8” thick 6061 Aluminum | 1/8” thick 6061 Aluminum | 1/8” thick 6061 Aluminum |
| Maintenance | None | None | None | None |
| Included Accessories | Comes standard with 6 stabilizing chains and 14 quick clips | Comes standard with 6 stabilizing chains and 14 quick clips | Comes standard with 6 stabilizing chains and 14 quick clips | Comes standard with 6 stabilizing chains and 14 quick clips |
| Total Sweeper Weight | 218.5 lbs | 252.5 lbs | 285.5 lbs | 318.5 lbs |
| Total Shipping Weight | 277.2 lbs | 320.4 lbs | 362.6 lbs | 404.9 lbs |
| Shipping Dimensions | 64″L x 13.5″W x 15″H | 76″L x 13.5″W x 15″H | 88″L x 13.5″W x 15″H | 100″L x 13.5″W x 15″H |
| Pricing Range | $3,535.00 CAD | $3,816.00 CAD | $4,082.00 CAD | $4,377.00 CAD |
Khamsin Heavy Duty Construction
A: 4 Steel anchor points for sway prevention
B: 5/8” Diameter Stainless Steel Pins
C: 10” x 3” Foam Filled bump wheels with 5/8” ball bearings rated at 225lbs each
D: Aluminum Covered Linear Height Adjuster Constructed of 3/16” and 1/4” thick steel
E: 3/8” Thick Bolted Steel End Caps
Khamsin Heavy Duty Construction – Detail
A: 5/8” Diameter Stainless Steel Pins
B: 10” x 3” Foam Filled bump wheels with 5/8” ball bearings rated at 225lbs each
C: ¼” thick aluminum end cap cover (to break magnetic circuit)
D: 3/8” thick x 4” x 6” steel angle end caps
E: 1/8” thick aluminum housing
F: 1/4” thick steel actuator frame bolted through aluminum housing and directly into tapped steel end caps
A: A = Distance from Magnet (Sweeping Height)
Note: Gauss (G) shown as the peak gauss measured in the center of the magnet at each distance.
Khamsin Dimensions End View
A: Extended
B: Retracted
A: A = Distance from Magnet (Sweeping Height)
Note: Gauss (G) shown as the peak gauss measured in the center of the magnet at each distance.
| 5 star | 0% | |
| 4 star | 0% | |
| 3 star | 0% | |
| 2 star | 0% | |
| 1 star | 0% |
Sorry, no reviews match your current selections
Price range: $212.00 through $529.00
$1,030.00
$1,242.00
The optional aluminum quick clean off sleeve is available for all 4.5” x 4.5” magnets in lengths of 62, 74”, 86” and 98”. These sleeves are far stronger than the PVC models (SEE DURABILITY TEST HERE) and protect the magnet assembly from impacts. PVC sleeves can also deform from the pressure of collected debris being pulled towards the magnet housing making them hard to pull off. The aluminum sleeves will not deform and the plastic rails on the inner corners of the sleeve allow for smooth operation. An extendable stainless-steel handle is also stored inside the sleeve to make removing the sleeve even easier. The aluminum quick clean off sleeve is a great solution for rough terrains and prevents having to buy a new PVC sleeve every time it cracks from hitting obstacles in rough conditions.
To clean off the Khamsin Adjustable Offroad Hanging Magnetic Sweeper when full of debris, just remove the Bump Wheel bracket on one end, slide the wheels off and pull off the Quick Clean Off Sleeve. All of the debris will drop off on the side of the magnet that you pull the Sleeve off. Clean off is easy, convenient and simple.
The KHAMSIN comes in 4 different sweeping widths (magnet bar lengths) of 62”, 74”, 86” and 98” to accommodate many different vehicle sizes. The Khamsin Adjustable Offroad Hanging Magnetic Sweeper can be front, mid or rear mounted on a variety of vehicles as long as enough clearance and space is present. We obviously recommend front mounting a magnet sweeper when at all possible so that you don’t run over the debris with your vehicle before picking it up.
As a hanging magnet, the KHAMSIN has no specific requirements of the vehicle to ensure FIT. You should however take a look at the CAD files showing overall dimensions of width and height to ensure the KHAMSIN will work with your intended vehicle and the anticipated mounting position. The Khamsin has a minimum retracted dimension of 12.37” inches (when raised) and maximum extended dimension of 25.37” inches (when lowered). The depth of the magnet from front to back (front wheel tip to back wheel tip is 10” inches.
The KHAMSIN utilizes permanently charged C8 Ceramic Magnets to provide a strong magnetic field with a maximum lifting height of 9” inches using a two and a half inch nail. Read more about how and why we measure power and performance this way.
The KHAMSIN will pick up a 2 ½” nail when the bottom of the magnet is 9” off the ground providing plenty of pickup power performance when operating on a moving vehicle.
Sweeping height is adjustable on the Khamsin Adjustable Offroad Hanging Magnetic Sweeper from a minimum of 2.5” inches with the bump wheels touching the ground, to a recommended sweeping height of 3” inches with the bump wheels 1/2” inch off the ground. The maximum suggested sweeping height, only if needed, is 5” inches. Magnet effectiveness will decrease as speed and sweeping height increase which is why we recommend a sweeping height of 3 inches if possible.
The KHAMSIN has 10” x 3” Foam Filled flat proof bump wheels with steel hubs and 5/8” ball bearings rated at 100 kg (220 lbs) capacity each
A: 6204-2RS Sealed high speed ball bearings
B: 5/8” OD 304 Stainless steel wheel bolt with serrated flange
C: 1300lbs load capacity
D: ADC 12 Cast aluminum hub
E: Precision machined aluminum bushings
F: 85 Shore A high elastic polyurethane
This wheel kit replaces the standard wheel and axle bolt assembly for a heavier duty wheel, hub and axle bolt. This 10” aluminum hub wheel fits on all widths of the Khamsin. This wheel is an upgrade that is built of stronger materials that can withstand more abuse in on and offroad settings. The sealed highspeed bearings keep dirt out so the polyurethane tread wheels can spin smoothly. The bearings and wheels are resistant to damage from impacts at speed so if the sweeper is expected to withstand heavy use in rough conditions this wheel will last longer and perform better than the standard option.
See how to easily mount a hanging magnet to the front bumper or rear hitch of your truck using our optional hanging magnet brackets.
A: Hanging Bracket C
B: 2” Inch Reveiver Mount Bracket
If you have a 2” inch receiver on either the front or rear of your vehicle you can mount a hanging magnet using one of the available Hanging Brackets (check the Hanging Bracket Selection Chart and FIT Guidelines to determine which based on the size of hanging magnet you choose), and the 2” inch Receiver Mount Bracket. These accessories are available for purchase and will be recommended accessories when you checkout.
A: Bumper Mount Bracket A
B: Hanging Bracket B
If you have a flat steel bumper on your commercial truck, you can mount a hanging magnet using one of the available Hanging Brackets (check the Hanging Bracket Selection Chart and FIT Guidelines to determine which based on the size of a hanging magnet you choose), and Bumper Mount Bracket A.
A: Push until holes line up
B: 2” inch receiver on truck
C: 2.5” inch to 2” inch steel receiver adaptor sleeve
If you have a 2.5” inch receiver on either the front or rear of your vehicle you can mount a hanging magnet using one of the available hanging brackets with the 2” inch receiver mount bracket and the 2.5” to 2” inch steel receiver adaptor sleeve accessory.
A: Hanging bracket D with easy height adjustment for hanging magnets with outrigger
Hanging Bracket D is compatible with the same magnets as Hanging Bracket C but features screw driven cable actuators on both ends for easy height adjustment (not needed if sweeper has built in height adjustment features).
A: Hanging Bracket E attaches to snowplow mount
B: Kubota snowplow mount for hanging bracket works with all Bluestreak hanging brackets
Hanging Bracket E is compatible with the same magnets as Hanging Bracket B (except Wrasse & Gobie) but features screw driven cable actuators on both ends for easy height adjustment (not needed if sweeper has built in height adjustment features).
- No Surprise Border / Tariff Fees After Checkout
- Fast Shipping
- All Items in Stock
English English 
English (Canada)
English (UK)
English (Australia)
Français du Canada
Español de México
Deutsch (Sie)
Português
Italiano
Polski
Nederlands
Ελληνικά
